Part Number:
BB-015
Accelerator pedal linkage rod made by Buttys bits in the UK. This is a double ended ball jointed rod that links your throttle/accelerator pedal to the linkage under the floor. It is very simple to fit using a thin 8mm spanner (supplied with kit). Suitable for left hand drive splitscreen busses from 1955 to 1967.
Part Number:
BB-013
This kit made by Buttys bits in the UK is a great upgrade to any left hand drive splitscreen bus from 1955 to 1959. The kit is a bolt on upgrade/replacement of the original accelerator linkage and gives a much smoother feeling to the accelerator pedal.
Please note: Do not clamp your accelerator cable. Tighten then undo half a turn as the cable end needs to rotate freely.
Part Number:
BB-014
This kit made by Buttys bits in the UK is a great upgrade to any left hand drive splitscreen bus from 1959 to 1967. The kit is a bolt on upgrade/replacement of the original accelerator linkage and gives a much smoother feeling to the accelerator pedal.
Please note: Do not clamp your accelerator cable. Tighten then undo half a turn as the cable end needs to rotate freely.
Part Number:
BB-012
This kit made by Buttys bits in the UK is a great upgrade to any right hand drive splitscreen bus from 1955 to 1967. The kit is a bolt on replacement of the original accelerator linkage and gives a much smoother feeling to the accelerator pedal.
Fitting instructions:
Remove the old cross shaft, push rod from the pedal and disconnect the throttle cable. Then clean the two square lugs where the original cross shaft went through the two holders, the new kit fits over the two square lugs allowing two bearing carriers to hang just below the original holders. The kit has to be fitted as it comes assembled. Remove the mounting bolts and fit the square washer over the square lug then fit the square bearing holder over the same lug and bolt up, leave loose while you set the cross shaft position then tighten up and make sure the new assembly moves without rubbing or catching on any other components. Now connect the pedal then the accelerator cable. The bearings will give a far smoother feeling to your accelerator pedal. Also the end plates are 20mm taller than the standard setup so it allows full throttle to be achieved easier on twin carb`d hex bar setups. The kit can be altered if you require less cable travel.
Part Number:
211-721-603
Accelerator pedal for all splitscreen busses from 1955 to 1967.
Part Number:
211-721-613
Accelerator pedal hinge for all Splitscreen busses from 1955 to 1967 and Bay Window busses from 1968 to 1979.
Part Number:
211-721-629/AQ
Accelerator pedal hinge pin with central groove for Split Screen vans from 1955 to 1967 and Bay Window vans from 1968 to 1972.
Part Number:
211-721-619
Accelerator pedal spring. Mounts below the pedal bracket to secure the hinge pin.
Part Number:
211-721-615
Replacement pushrod for the accelerator pedal on left hand drive splitscreen busses from 1955 to 1967.
Part Number:
214-721-615
Replacement pushrod for the accelerator pedal on right hand drive splitscreen busses from 1955 to 1967.
Part Number:
211-721-621
Rubber seal in the cab floor for the accelerator pushrod on all splitscreen busses and early bay window busses from 1968 to 1972.
Part Number:
211-721-617
Compression spring for the accelerator pedal push-rod, two required. Also used for the fan housing air flaps, four required.
Part Number:
211-721-631/KIT
Accelerator linkage repair kit for left hand drive splitscreen busses from 1955 to 1967. Kit consists of 1x push rod, 1x lever, 1x clevis pin, 1x cotter pin and 2x compression springs.
Part Number:
111-129-901
Accelerator cable return spring. See below for various vehicle uses.
Part Number:
111-721-555/U
4572mm universal use accelerator cable. This clever over long accelerator cable with two different types of front fixing ends is the perfect item to carry as a breakdown spare for when the accelerator cable goes and leaves you stranded at the side of the road. Just cut off the unneeded end , feed through, and trim to length.
Perfect to sort out you or your friends, or for when you feel that good Samaritan moment coming on for your fellow stranded dubbers. Also useful when fitting non standard carb/engine set ups.
Part Number:
211-721-555/A
3564mm long accelerator cable. This cable can be used for all Splitscreen vans from 1955 (chassis number 20 117-902) up to 1964 (chassis number 2x50 036 651 where x can be any number from 1-8 denoting model type). Additionally, for right hand drive vehicles, this cable can also be used for all Barndoor vans up to 1955, (chassis number 20 117-901).
Part Number:
211-721-555/C
German made 3576mm accelerator cable for all left hand drive and right hand drive splitscreen busses from 1964 to 1967.
Part Number:
ACE0002Accelerator cable roller guide. Mounts on to the gearbox to stop the accelerator cable cutting into the gearbox.
Part Number:
211-721-163/A
Return spring for the brake pedal on left hand drive splitscreen busses from 1955 to 1967.
Part Number:
211-703-291
Solid rubber buffer to cushion the return action of the clutch pedal on splitscreen busses from 1955 to 1967.
Part Number:
131-721-349
M7 adjusting wing nut for the gearbox end of the clutch cable on vehicles with oval ended release arm, normally 1965 and onwards.
Part Number:
211-721-351
Clip/pin to secure the clutch cable to the base of the clutch pedal.
Part Number:
111-721-349/A
M7 adjusting nut and lock washer for the gearbox end of the clutch cable on vehicles with round ended release arm, normally up to 1965.
Part Number:
311-721-173/A
Rubber pad for the brake and clutch pedals.
Part Number:
211-721-383
Inner felt sealing pad for brake or clutch pedal shaft on splitscreen busses from 1955 to 1959.
Part Number:
211-721-383/B
Inner foam sealing pad for the brake or clutch pedal shaft. These are self adhesive and stick to the cab floor underneath the floor mat to seal the hole around the pedal.
Part Number:
211-721-387
Rubber seal for the clutch and brake pedal arms, fits below the cab floor on splitscreen busses from 1955 to 1967.
Part Number: 211-721-647
Rubber pedal pad to fit accelerator pedal, Fits Splitscreen and Baywindow buses 50-79.
Part Number:
211-721-629
Accelerator pedal hinge pin with central groove for Split Screen vans from 1955 to 1967 and Bay Window vans from 1968 to 1972.
These hinge pins are produced in house in the UK from steel which is then hardened for a hard wearing and long lasting finish unlike the stainless steel and non hardened steel reproductions.