Part Number:
211-119-163/A
Thermostat push rod for all 1200cc to 1600cc Type 1/upright engines.
Part Number:
111-198-123/A
Mounting kit for main engine cooling fan to dynamo/alternator. Includes the fan hub, main nut and two washers. Suitable for all upright/Type 1 based air-cooled engines.
Part Number:
113-119-031/A
316 mm engine cooling fan for single port engines with oil cooler inside the original fan-housing (Non-doghouse).
Part Number:
131-119-031
368mm engine cooling fan to fit 1300cc to 1600cc Twinport engines with Doghouse oil cooler, and many aftermarket non-doghouse fan housings.
Part Number:
111-119-123/A
Mounting hub for the main engine cooling fan on the rear of the generator/alternator on all Type 1 based upright aircooled engines.
Part Number:
111-119-135
Spring washer for the main engine cooling fan on the rear of the generator/alternator on all Type 1 based upright aircooled engines.
Part Number:
111-119-141/A
Mounting nut for the main engine cooling fan on the rear of the generator/alternator on all Type 1 based upright aircooled engines.
Part Number:
111-119-133/B
Flat washer for main engine cooling fan on all upright Type 1 style engines.
Part Number:
113-119-025/J
30 hp style doghouse fan shroud with fresh air outlets, finished in black. Fitted with correct internal ducts/vanes. These fan shrouds should be used with twin port cooling fans.
Item is supplied in a packing paint for transit. For a long lasting finish we advise that this item is painted or powdercoated.
Part Number:
043-129-893
Accelerator cable conduit through the fan shroud on most air cooled vehicles.
Part Number:
113-119-279
Fanhousing cooling flap return spring. Fits both doghouse and non doghouse fanshrouds.
Part Number:
211-721-617
Compression spring for the accelerator pedal push-rod, two required. Also used for the fan housing air flaps, four required.
Part Number:
211-119-471/KIT
Three piece backing plate kit for engines using an alternator or 30 amp dynamo. Will not fit 38 amp dynamos.
The backing plates are coated in a black packing paint. We recommend that the item is either painted or powder coated for a long lasting finish.
Part Number:
113-198-303
Pair of single port cylinder shrouds. Finished in black.
Items are supplied in a packing paint for transit. For a longlasting finish we advise that these items are painted or powdercoated.
Part Number:
113-119-517/R
Front engine tinware over the gearbox for all single port engines.
Part Number:
043-119-351/B
Tinware for under the left cylinder head, for use with 1300cc to 1600cc engines. Item is supplied in a packing paint for transit. For a long lasting finish we advise that this item is painted or powder coated.
Part Number:
211-957-905
Rubber grommet for Splitscreen van speedo cables, where the cable passes through the front panel to the underside of the van.
Part Number:
111-115-491
Oil breather/overflow pipe to tinware seal for use on upright Type 1 based engines.
Part Number:
113-119-571
Fresh air tube sealing grommet for all upright air cooled engines.
Part Number:
111-501-159/B
Fresh air tube clamp for all upright air cooled engines. 44-46mm diameter.
Part Number:
113-119-585/A
Fresh air tube sealing grommet for all upright air cooled engines.
Part Number:
028-129-087/F
Aluminium hose for connecting fan housing outlets to heat exchangers. Also for late air bath hot air bypass tubes. 500mm length and 50mm internal diameter.
Part Number:
028-129-087/A
Standard 50mm diameter cardboard air hose for upright type 1 based engines. Used for connecting the fan housing to the exhaust.
Part Number:
113-255-165
Connecting pipe for exhaust to fresh air tube for all upright air cooled engines. 44-46 mm diameter.
Part Number:
113-255-355/M
Heater tube from heat exchanger to body, 360mm long with 60mm diameter ends.
Part Number:
111-251-260
Exhaust pre-heat block off plate. Blocks the pre-heat section of the muffler on original OKRASA 30 horse power engines and Wolfsburg West reproduction dual port 30 horse power engine kit.
Part Number:
211-255-359
Aluminium pre-heater to air filter hose, 25 x 900mm.
Part Number:
111-255-101/C
Heat exchanger for the left side of 25 and 30 horse power engines in beetles and splitscreen vans.
Part Number:
111-255-102/C
Heat exchanger for the right side of 25 and 30 horse power engines in beetles and splitscreen vans.
Part Number:
043-298-250
Pair of heat exchangers including gaskets, air hose and fitting kit.
Part Number:
043-255-107/F
Left side heat exchanger with stainless steel tubing & aluminized box for better rust prevention.
Part Number:
043-255-108/F
Right side heat exchanger with stainless steel tubing & aluminized box for better rust prevention.
Part Number:
113-255-341/A
Clamp for mounting the exhaust to the heat exchanger on most aircooled vehicles from 1963 to 1979.
Part Number:
113-255-737
Securing clip for the pre heat tube to air filter. Two required per vehicle.
Part Number:
113-119-352/C
Lower Right cylinder under tin, under the thermostat, for use with 1300cc to 1600cc engines.