Part Number:
111-129-921
Swivel clamp for accelerator to cable to carburetor operating arm and heater cable to heat exchanger operating arm on most air-cooled VWs.
Part Number:
058-129-413/D
12 volt fuel idle jet cut off valve for the following carburetors.
- 30 PICT
- 31 PICT
- 30 PICT 2
- 34 PDSIT-2
Part Number:
049-129-412/C
12 volt carburetor air cut off solenoid valve for the carburetor.
Part Number:
043-129-941
Rotary action dual carburetor linkage for Weber IDF and Empi carburetors.
Part Number:
113-129-191/G
12 volt auto choke unit for 30-34 PICT Solex Carburetors.
Part Number:
043-129-893
Accelerator cable conduit through the fan shroud on most air cooled vehicles.
Part Number:
211-129-587
The larger diameter of the main body on the alternator means that 34 PICT carbs foul when fitting an alternator conversion. This 10mm spacer lifts the carburetor up to provide the required clearance.
Part Number:
113-129-881/A
Carburetor return spring.
Part Number:
111-198-569/C
Carburetor rebuild kit for 31 PICT 4 carburetors. Includes gaskets and diaphragms, but not jets.
Part Number:
111-198-569/ZW
Carburetor rebuild kits for 28 Pict, 30 Pict and 34 pict 3 carburetors. Complete with floats, filter and needle valve. Please note this kit is not suitable for 31 Pict 4 carburetors.
Part Number:
113-129-707/C
Carburetor base gasket for 34 Pict 3/4 carburettors
Part Number:
N 13 778 1
Carburettor base gasket for the carburettor base to the manifold on single port engines, 30/31mm PICT.
Part Number:
211-129-615/F
Air cleaner to carburetor rubber elbow.
Part Number:
111-129-781
Pancake style air filter for use on stock carburetors. Supplied with a paper filter element, chrome base and top. Fitted with a 1/2'' hose barb for use with the standard oil filler/breather. The diameter of the air filter is 165mm and the diameter of the opening is 52mm.
Part Number:
111-129-741
Aftermarket pancake style air filter for use on stock carburettors. Supplied with a foam filter element, chrome base and top. Fitted with a 1/2'' hose barb for use with the standard oil filler/breather.
Part Number:
113-129-701/K
Single port inlet manifold for 1300cc to 1600cc Type 1/upright engines.
Part Number:
311-129-707
Standard single port inlet manifold/cylinder head crush gasket. For use on 1300cc to 1600cc Single port engines.
Part Number:
113-129-709/G
Twin port intake manifold end casting for the left hand side of the engine.
Part Number:
113-129-710/G
Twin port intake manifold end casting for the right hand side of the engine.
Part Number:
113-129-717/A
Inlet manifold Gasket for twin Port engines.
Part Number:
113-129-729/B
Rubber seal for the inlet manifold on twin port, upright Type 1 based engines.
Part Number: N 020 355 1
5.5mm Rubber fuel hose, suitable for modern fuel blends, including E10 fuel with 10% Bio Ethanol. Suitable for use on normally aspirated carbureted engines.
Part Number:
N 900 996 01
Nitrile rubber fuel hose with cotton braid, suitable for modern fuel blends, including E10 fuel with 10% Bio Ethanol. Suitable for use on normally aspirated carbureted engines.
Normal rubber fuel hose is susceptible to perishing and cracking with modern fuels, leading to risk of engine fires
Part Number:
111-127-537/A
Crimp type fuel hose for 11mm to 13mm outer diameter fuel hose.
Part Number:
N 24 528 1
Screw type fuel hose clip for 8mm to 12mm outer diameter fuel hose.
Part Number:
311-971-913
Rubber grommet for 6mm fuel line through engine tinware